Flash the latest firmware to your GTi touchscreen, GTi dongle or FluxDrive straight from the browser. No Arduino IDE, no CLI.
Browser not supported
This flasher needs the Web Serial API. Open this page in Chrome, Edge, or Opera on desktop. Firefox and Safari are not supported.
Install
Pick your board, plug the device into a USB port, then click Connect and choose the matching serial port from the list.
First-time installs will erase the flash; existing settings on the SD card are untouched.
Device already running the firmware? Skip the cable: Download .bin and drop the file on the device's own web page (Config → Firmware card), or put it on the SD card for the on-device FW UPDATE. This downloads the app image only — exactly what over-the-air updates expect.
Before you start
Use a data cable. A power-only USB cable is the #1 support call: the device boots and WiFi works, but no serial port ever appears — on any computer. If in doubt, try the cable on a phone: file transfer must work.
Boot mode. If no serial port shows up after plugging in: hold the small BOOT button while inserting the USB cable (or hold BOOT and tap RESET), then release. The port appears within a few seconds.
Close the Arduino IDE and any other serial monitor — Windows allows only one program on the port.
XIAO owners: connect the external u.FL antenna before first use. The XIAO has no usable onboard antenna; without it, WiFi will look broken.
First boot — touchscreen (JC3248)
SD card: FAT32, with your .ADF (Amiga) or .DSK (ZX/CPC) files — loose in the root or one folder per game (cover art .jpg/.png and info .nfo files next to them are picked up automatically). The device creates CONFIG.TXT on first boot; you rarely need to edit it by hand.
Power & connect: plug the device's USB into the Gotek drive. It powers the board and carries the floppy data — FlashFloppy sees a USB stick. Any 5V USB source works for setup on the bench.
WiFi portal: the device broadcasts its own network:
SSID GotekOMEGA — password gotek1234
Connect with a phone or laptop and open http://192.168.4.1. That is the full web interface: browse the library, insert disks, and enter your home WiFi credentials on the Config tab.
Installed before v0.25.4? Then the network may be called Gotek-Setup with password retrogaming — it keeps whatever it was set to.
On your home network the device is reachable at http://gotek.local (rename via MDNS_NAME=gotek1 etc. when you run several).
Updates from here on are wireless: drop a new firmware file on the web page's Firmware card, or use the on-device FW UPDATE options. The cable was a one-time affair.
Picture upside-down? Tap FLIP 180 on the splash — the choice is remembered.
First boot — screenless dongle (SuperMini / XIAO)
Plug the dongle into the Gotek's USB port (it draws its power there too).
It broadcasts GotekOMEGA-xx (a unique suffix per dongle) — password gotek1234.
On your phone: join that network and open http://192.168.4.1. The SuperMini shows the same app as FluxDrive (in the NEO skin, or your own): load a disk image from the phone (.ADF, .DSK, .IMG, .HFE…) and it mounts on the Gotek instantly.
Home WiFi, the skin and firmware updates are in the app under More; the setup page for the access point name and password and ESP-NOW is More > Setup page. The SuperMini handles DD images (880 KB); the XIAO also does HD (1.76 MB).
First boot — FluxDrive rev A
Flash with the Amiga idle: no disk access while installing, the drive restarts during the install. A first install that erases the flash also clears the disk stored in the drive and its WiFi settings.
It broadcasts GotekOMEGA-xx (a unique suffix per board) — password gotek1234. Join that network: the phone's sign-in window shows the Wi-Fi page to enter your home WiFi (or open http://192.168.4.1).
On your home network it shows up as fluxdrive-xxxx (its own suffix, also in your router's client list) and answers at http://fluxdrive-xxxx.local, or use its IP.
FluxDrive takes DD ADFs of exactly 901,120 bytes. Its page shows both drives: drop an .ADF and choose DF0 or DF1.
DF1: FluxDrive can also be DF1. Switch it on with DF1 on on its page (or fdconsole.py --port COMx "df1 on" over the USB console; the setting is kept) and reset the Amiga; load a disk from the page, the USB stick or fdconsole.py --port COMx load1 disk2.adf. DF1's disk is kept in FluxDrive's flash and comes back after a power cut. DF1 is writable (its write protect switch on the page) once FluxDrive has seen DF1's motor signal: on rev A that is the optional motor wire; without it DF1 stays write-protected.
USB stick: put a FAT32 stick (MBR partition) with ADFs in the USB-A socket and power up with no cable in the USB-C (a PC on the USB-C at power-up makes that port the console instead; restart FluxDrive without it to use a stick). The stick is powered by the Amiga, so the Amiga must be on. The page lists the stick's folders and ADFs: tap DF0 or DF1 to load one; a load is stored in the drive like an upload, and what the Amiga writes to a disk from the stick (high scores, saves) goes back into its .adf on the stick a few seconds later, like a Gotek. ADFs can be renamed and moved to another or a new folder from the page. Updates while a stick is in use go through the web page (the console is off then).
Knob (optional): with an EC11 rotary encoder on the board, the OLED gets a menu: turn to pick DF0 or DF1, press for its menu (load from the USB stick, eject, write protect, an empty disk on the stick, name the file after the disk), hold for Settings (Wi-Fi info, DF1 on/off, language).
The app:http://fluxdrive-xxxx.local/ is one app for phone and laptop (bottom tabs on a phone, a side rail on a laptop): Drives (both drives with the game's cover, eject, write protect, an empty disk), Games (the games on the USB stick with their cover art and info: a folder's .png/.jpg and .nfo), Files (load, rename, move, upload, delete, and what is on an ADF), WebDAV (your NAS, HTTP or HTTPS: browse, load a game into DF0 or DF0+DF1 straight away, or keep it on the stick) and More (skin, language, Wi-Fi, firmware). Favourites are kept on the FluxDrive. Its colours follow the chosen skin (NEO by default, or upload a GTi .gts).
Updates:Download .bin here and pick it under More > System > Update firmware in the app (http://fluxdrive-xxxx.local/). FluxDrive only accepts FluxDrive firmware, and writes it while the Amiga is not using the drive.
AmiHID board v1
Download mode first: the AmiHID's USB-C is the port for your mouse or pad, so a PC only sees it in download mode. Take it out of the Amiga, connect it to the PC with a data cable, hold BOOT, tap RESET and release BOOT. Then click Connect and pick the serial port that appeared.
Keep your settings: leave Erase device unticked when the installer asks. Erasing also clears the button profiles and the Bluetooth pairings.
After the install, tap RESET (or unplug it) so it starts the new firmware, and put it back in the Amiga with the Amiga switched off.
There is no wireless update yet: every update goes through this page and the cable. Download .bin does not apply to the AmiHID.
Setting it up: the AmiHID tester connects over Bluetooth and shows every button and axis live, sets the buttons per device, tests the Amiga port and pairs Bluetooth devices.
Troubleshooting
No serial port appears: data cable? BOOT held while plugging in? On Windows, a port stuck at "access denied" is freed by disable/enable in Device Manager or a reboot.
Dongle seems dead right after flashing: normal — it does not leave download mode by itself. Unplug and replug, then it boots the new firmware.
Gotek shows no drive but a PC does (or vice versa): power the device from the Gotek's own USB port, and check the cable again. FlashFloppy is pickier than a PC.
gotek.local not resolving: use the device's IP (shown on the touchscreen's CONFIG page, or in your router's client list). Android phones often lack mDNS — use the IP there.
WiFi network called Gotek-FAIL-PSRAM: the board reports a hardware/build mismatch — get in touch, that unit needs attention.
iPhone: "choose a file" greys everything out: fixed in v0.25.3 — flash the current firmware from this page first, or do that one update from a desktop browser.